Winload exe как восстановить windows 10 0xc000000e

You get 0xc000000e error code on Windows 10 when there is a problem with boot loader or wrong Boot configuration data.

If you have multiple disks, only one of them is the boot disk.

So, the boot configuration data is stored on one disk of all the related settings to boot different Windows OS.

Even though you use bootrec commands to fix the boot loading options, it is important you change the order of the boot disk. You can have Metro bootloader or Windows 7 type, but the cause of the problem is the same.

The typical error message for 0xc000000e will be like this –

Recovery
You’re PC/Device needs to be repaired…….
File: \Windows\system32\winload.efi
Error Code: 0xc000000e

This can appear when your Windows 10 OS was deleted on one HDD, which is the boot drive. The boot order options could also have changed.

For example, having two disks like Samsung 850 Evo 1TB and Samsung SM951 m.2 NVME 128GB, can complicate the issues.

You may get confused that the problem is with the hardware or some software. But many-a-times the real problem is with the boot loader configuration stored on your disk.

There are different causes which can cause this Windows 10 error code issue.

1. A required device isn’t connected or cannot be accessed
2. Required device is inaccessible
3. The selected entry could not be loaded
4. The selected entry could not be loaded because the application is missing or corrupt
5. The boot selection failed because a required device is inaccessible.

Source : thewindowsclub.com

As you can see above, the real cause for this error code 0xc000000e is either winload.exe file is not accessible or is corrupt or the boot loader location of Windows 10 is not accessible.

How to Fix Error Code 0xc000000e in Windows 10

The following solutions may be tried to fix this problem.

1. Change the boot order of the disk, if you have multiple disks like HDD and SSD.
2. Use Windows 10 Startup Repair feature using Installation Disk
3. Apply BCD command to rebuild it manually
4. Make your Disk Online
5. Try third-party software

Most-of-the-times, the above fixes will show you the way to solve error code 0xc000000e in Windows 10.

1. Change the Boot Order in BIOS

The first preliminary fix is to check, whether the boot disk is the first disk loading during booting.

This can be done, by changing the options in BIOS.

Most of the times, pressing F2 or F2 or F10 or ESC or DEL keys during booting will take you to BIOS settings.

This depends on your PC manufacturer model and the BIOS software you are using.

For example on Phoenix AwardBIOS CMOS setup utility, under “Advanced BIOS features” you have the following options.

1. Hard Disk Boot Priority
2. First Boot Device

You can have multiple devices like USB, DVD, HDD etc connected to your PC.

1. First make sure your HDD is the First Boot Device.
2. If you have multiple hard disks or solid state drives on the same system, then you have to use Hard Disk Boot Priority.
3. Go to the first option and press Enter. Then select the disk which is your boot disk and press F10.

It will save your changes and Restart. If nothing is corrupt, you should be able to fix error code 0xc000000e and enter Windows 10.

1. Use Startup Repair in Windows 10 Installation Disk

Create a bootable Windows 10 installation disc. This could be either a DVD or USB. You can use an utility like Rufus to boot from USB. Otherwise, you can use software like MagicISO to boot from DVD.

Insert the appropriate hardware and change the BOOT options to load from it, as mentioned above.

Source : https://www.laptopmag.com/articles/windows-10-advanced-startup-options-menu

The installation disc will boot up and select language and keyboard layout. Click Next. You will be taken to the next screen. On this screen, at the bottom you see, “Repair your Computer”.

Then click “Troubleshoot” > “Advanced Options” > Startup Repair.

If it’s a small issue, this will fix problems that keep Windows from loading. This will also automatically solve the 0xc000000e error, as startup problem is the main cause for this issue.

1. Rebuild BCD manually

This solution is appropriate if the problem is due to corrupt boot loader. If the boot configuration data has been erred by some hardware change, then the BCD commands will fix this. This is the most common solution for error code 0xc000000e and in many-a-times solve the problem.

1. Boot using the Windows 10 Installation dsic.
2. Then go to “Advanced options”.
3. But this time select “Command Prompt”.
4. Enter the following commands one by one.

bootrec /fixboot
bootrec /scanos
bootrec /fixmbr
bootrec /rebuildb--

Upon completion of each command, you will get a successful message. If you get any other error message then you  can try these troubleshooting steps.

1. Access is denied while apply the fixboot command.

Then you have to type the following commands in the Command Prompt.

Step 1: Type diskpart and press Enter key.

Step 2. Type list disk and press Enter. Now check disk number to identify boot disk, this is usually Disk 0. if not, use the correct boot disk number.

Step 3. Type select disk 0 (or your boot disk number) and press Enter.

Step 4. Type list volume and press Enter. Now look for the volume number of EFI partition.

Step 5. Type select volume 1 and press Enter. (Change volume to your number)

Step 6. Type assign letter=V: and press Enter. V: can be replaced by any drive letter that is not in use by any partition.

Step 7. Type exit and press Enter.

Step 8. Now type V: (or the drive letter you just assigned) and hit Enter.

Step 9. Type md \efi\microsoft\boot\ and hit Enter.

Step 10. Type — /d V:\efi\microsoft\boot\ and hit Enter.

Step 11. Now type bootrec /fixboot command, the problem should be solved now.

Step 12. b–boot c:\windows /l en-us /s V: /f all

The below YouTube video will show how to fix the Access is denied error while using the Fix MBR command. 

If you have multiple OS on the same PC, you can add all of them to the new boot configuration. A prompt with different options is displayed during the /scanos command.

If this still fails to boot your computer, then the correct order of the boot disc is the problem.

So using the BIOS settings, you have to do trial and error of the correct disc on which the boot loader is situated.

This happens when you have multiple disks.

1. Make the Boot Disk Online and Scan Disks

Sometimes, the boot drive can go offline and is not added to the boot loader settings. Then you have to apply the following commands.

In the Command Prompt of your Repair Disc or Installation disc, as mentioned before, enter the following commands.

1. diskpart
2. list disk
3. list volume
4. select disk # (or) select volume #
5. online disk # (or) online volume #

Press Enter and restart the computer.

1. Use EasyBCD kind of repair software

There are several third-party software that will recover your corrupted boot loader. They will also scan the disks and do other functions. They are kind of repair software. You just have to boot them using an USB or DVD and make the disc bootable.

Once loaded, find the right options to regain your old boot order. This can check your hard disk for bad sectors and also make the correct drive bootable. The following are some of the software.

1. Easy Recovery Essentials
2. AOMEI Partition Assistant
3. EasyBCD

Some of the case-studies of the above error code can be like this.

I just upgraded to Windows 10 on my laptop from windows 7 on a solid drive, All seemed to work fine at first, then I had this boot failure problem.

“Recovery
Your PC need to be repaired
File: \Windows\system32\winload.exe
Error Code: 0xc000000e
You’ll need to use the recovery tools on your installation media, etc……
Press Enter to try again
Press F8 for Start-Up Settings”

https://answers.microsoft.com/en-us/windows/forum/all/windows-10-needs-to-be-repaired-error-code/b510c535-0c4f-4c72-adfe-dbbaf54a086f

I updated my Windows 10 OS few days back due to the forcible prompts to update.

My laptop went out of power completely yesterday and after that I get the error Error Code 0xc000000e during startup.

Tried many options like below :

– bootrec /fixmbr
– bootrec /fixboot –> Got Access is denied at this step
– bootrec /rebuildb– –> Total identified Windows installations: 0

The 2 TB SATA drive is not being recognized. I have important data in the hard drive, any ideas how to recover the data by a repair?

https://answers.microsoft.com/en-us/windows/forum/all/windows-10-error-code-0xc000000e-during-startup/a0d73d2a-551d-4904-bf0f-9802aca1c878

My Final Thoughts

As you can see, the main cause of this error code 0xc000000e is to install the winload.exe on each OS and repair the boot configuration data. Then load the correct boot hard drive and you are back to normal.

Sometimes, you have to try 2 to 3 different solutions mentioned above to solve your problem. Otherwise, you can use any of the software told above to repair your startup problems caused by the above error code.

Applying the commands in the Command Prompt properly is also important.

If you can rebuild MBR using the bootrec commands, then this error code will disappear. But sometimes, you may get error like access is denied, which can be fixed as mentioned above.

If you have solved your error, mention your experience in the below comment section.

The startup error 0xc000000e on Windows is pretty annoying since it makes it difficult for the individual to run the operating system properly. It occurs as a consequence of an erratic shutdown or restarting of the system, which could be caused by a power outage or a rapid system crash, corrupting all boot configuration information. In this article, you will get to know how to fix your boot configurations.

Reasons and Solutions for the ‘0xc000000e After Clone Windows 10’ issue

The Reasons Behind the ‘0xc000000e After Clone Windows 10’ Problem

After a clone, a Sysprep, an image, or even a Windows upgrade, the 0xc000000e after clone windows 10 problem is common. The Winload will be caused by several causes. After cloning, the EFI file can be missed.

1. The registry key was entered incorrectly in this case. To avoid having to modify the registry entry after cloning, the source disk, as well as the target disk, need separate IDs both for volumes with drive letters.
2. Incorrect UEFI configurations. Not only the boot files but also algorithms required hereby UEFI and Legacy modes are different. Consequently, make certain that the relevant parameters are configured for your target disk.
3. The BCD data have been corrupted. Cloning can sometimes cause harm to the BCD storage files, resulting in the appearance of this Winload. EFI 0xc0000225 error message or any other Winload-related message concerns EFI not being present First and foremost, BCD files must be repaired.

Ways to Fix the Error (Solutions)

You have the following short solutions based on the issues; try checking them out.

Solution 1: Disable Secure Boot

It will prevent your software from reaching the winload. efi file when you are using a device that is based on the UEFI technology. For this reason, you should launch BIOS or UEFI using the following keys: F2, F8, F12, ESC, DEL (based on the Computer model), and then locate the Secure Boot button in the BIOS and UEFI and finally, you have to disable it.

The next method should be tried if the first one does not work to solve the error.

Solution 2: Use DiskPart to Repair

Step 1: First, you have to enter into your computer’s Windows installation media.

Step 2: Then, you have to navigate to the Repair your computer option.

Step 3: There, you have to choose the Advanced Options.

Step 4: Now, you have to click on the Troubleshoot button and go to the Command Prompt.

Step 5: To resolve the winload.EFI missing problem on Windows 10, run the following commands:

• diskpart

• list volume
• select volume=n (where n refers to the system reserved segment’s volume number that has the label “System” on there).
• assign letter=m (m is the right drive alphabet which is not currently in use).
• bcdboot c:\Windows /sm: /f UEFI (To activate the system, change the character “c” with the character of the system partition labeled with the phrase “Boot.”).

Once your system has been restarted, check to see whether the winload. efi absent after clone problem has been resolved; if not, consider next method.

Solution 3: Check and Repair Windows System Files

Step 1: Then, using the Windows installation media, launch Command Prompt and type in the command below.

• sfc /scannow

Alternatively, you can use the commands below to resolve the winload.exe absent after clone error:

• bcdedit /enum | find “device” (to locate the disk letter assigned to the Windows installation partition)
• sfc /Scannow /OFFBOOTDIR=C:\ /OFFWINDIR=C:\Windows (change the alphabet to the drive letter of the Windows partition that was installed).

Solution 4: Fix Corrupted BCD Files

If none of the methods listed above are successful, try this one. First and foremost, you must build a Windows 10 install DVD, after which you must boot into the recovery state and recreate the boot configuration data (BCD) store. If you have got a Windows 10 installation DVD, you can refer to next for further information.

Step 1: First, you have to launch the Windows Recovery Environment using the installation media.

Step 2: Then, you have to navigate to Repair your computer and select Advanced Options.

Step 3: Now, you have to click on the Troubleshoot option and go to the Command Prompt.

Step 4: Next, you have to run the commands below for executing each command for fixing the issue.

• bootrec /fixmbr
• bootrec /fixboot
• bootrec /scanos
• bootrec /rebuildbcd

If the commands  above are not successful, you are recommended to try the below commands listed:
bcdedit /set {bootmgr} device boot
bcdedit /set {default} device boot
bcdedit /set {default} osdevice boot
bcdedit /set {default} device partition=c:
bcdedit /set {default} osdevice partition=c:
bcdedit /set {default} path \windows\system32\winload.efi

Restart your computer to check if you are a success.

You can make your own Windows installation CD when you don’t even have one. AOMEI Backupper Standard, a strong third-party media production tool, will come in handy. Try downloading AOMEI Backupper Standard to generate WinPE bootable disk before attempting to fix winload. efi if it is absent or contains errors after cloning. Another option is to create an at minimum 16-gigabyte USB flash drive & link it to the pc.

Step 1: First, you have to install the FreewareWin and then, open it.

Step 2: Once you open this, you have to select the Tools and click on Create Bootable Media on the windows taskbar of the program.

Step 3: If you’re creating media, select Bootable Disc Type from the drop-down menu. You can either build a Linux bootable disc depending on the kernel or maybe a Windows boot disc built on Windows PE. And then click on the Next button to continue.

Select the button Download WinPE creating an environment again from the web to start the process.

Step 4: Now, you have to select the USB Boot Device. Then, click on the Next button to create the Windows 10 bootable media.

You can also load the WinPE image to a CD or DVD, or export it like an Image file.

After making bootable media (which takes only a few moments), start the system from the media, which will launch AOMEI Backupper immediately. From there, select Tools and then go to the Windows Shell Command to perform the command.

Then, using the aforementioned commands, you can simply fix the Winlaod .efi missing after the clone error and solve BCD problems. Then you should check to see if your PC is bootable. Furthermore, if you encounter problems such as File:EFI:MicrosoftBoot: BCD Error, Windows 10 BCD file missing, Transcend SSD Scope not working for system clone, Seagate DiscWizard not cloning problem and so on, this shareware will be of assistance to you in solving your problems.

You can build a recovery environment to include AOMEI Backupper inside the Windows boot selections; the recovery environment would simply operate as the Windows bootable media.

Best Free Way to Avoid Winload.efi Missing After Clone

If you are experiencing troubles after or during cloning, then you can seek assistance from AOMEI Backupper, which can enable you to duplicate hard disks, such as cloning HDD to SSD or bigger HDD, even cloning Windows toward a fresh HDD.

Windows 10 is supported by this powerful hard drive replicating software that supports a wide range of languages including English, French, and German. It also supports various dialects of Japanese as well as Summarized Chinese, as well as Classical Chinese. It also offers a variety of features including Spanish, Turkish, and, Dutch.

Using the procedures described below, you can avoid getting the error winload. efi missing after clone or 0xc000000e after clone windows 10, among other things. It is recommended that you clone the bootstrap drive to NVMe to make the highest speed out of the replicated SSD.

Step 1: First, you have to select the Clone and click on the Disk Clone on the window.

Step 2: Then, you have to choose the Windows system disk like a clone to the source drive, and click on the Next.

Step 3: Now, you have to choose a bigger HDD or SSD as a point, and click on the Next.

Step 4: When you have finished previewing the actions, click Start Clone to prevent the Winload.efi missing after clone error in Windows 10.

Conclusion

When this error occurs, you cannot run your operating system properly. You can apply the methods above to fix the error code and perform the system correctly.