Windows 7 с драйверами sata raid

• 64-bit Windows 7 Ultimate
• 6GB RAM
• Intel i7 920
• Intel X25-M SSD 80GB 2,5″
• Club 3D Radeon HD5750
• GA-EX58-UD4P Motherboard

I’ve been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI.

This motherboard supports two different RAID controllers, the Intel’s ICH10R and Gigabyte’s SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I’ve been trying to make it work.

When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: «Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do.»

First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives «This computer does not meet the minimum requirements for installing the software» error. I then tried Intel’s Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte’s site), but it resulted in exactly the same error.

I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD’d, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte’s RAID enabled (while the ICH10R RAID disabled) and it booted just fine.

So then I thought, that maybe I can’t install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: «rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf» but it gave «Installation failed.»

So I’m clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don’t want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks.

I mean why would I need to re-install operating system to add RAID setup?

For those of you (like me) who have an AMD system with an SB8xx or SB9xx controller (and possibly other models as well), try this guide: http://www.wikihow.com/Enable-RAID-or-AHCI-without-Reinstalling-Windows-(for-AMD-SB85-or-SB8XX-Controllers)

This process worked for me. I have a MSI 990FXA-GD80 with an AMD CPU running Windows 7 64-bit.

The guide is pretty detailed, so I will only summarize it here.

1. Set your BIOS to AHCI or RAID mode (whichever will be your final selection).

2. Boot into linux (a live CD is sufficient) and run the command lspci -vvnn. This lists all PCI devices. Find your RAID controller and write down the vendor ID (4 digits), device ID (4 digits), and subsystem ID (8 digits with a colon). I found this list of PCI vendor IDs informative: http://www.pcidatabase.com/vendors.php?sort=id.

3. Change the BIOS back to IDE mode.

4. In Windows, copy your RAID driver (probably named ahcix64s.sys) to C:\Windows\System32\drivers.

5. Import the registry information below (create a text file with the .reg extension). Be sure to set the vendor ID, device ID, and subsystem ID.

6. Set your BIOS to AHCI/RAID mode.

Registry information:

Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\CriticalDeviceDatabase\pci#ven_1002&dev_4393&cc_0104]
"ClassGUID"="{4d36e97b-e325-11ce-bfc1-08002be10318}"
"Service"="ahcix64s"
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s]
"Type"=dword:00000001
"Start"=dword:00000000
"ErrorControl"=dword:00000001
"Tag"=dword:00000001
"ImagePath"="system32\\drivers\\ahcix64s.sys"
"Group"="SCSI Storport"
"DisplayName"="AMD AHCI Compatible RAID Controller"
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s\Parameters]
"BusType"=dword:00000008
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s\Parameters\PnpInterface]
"5"=dword:00000001
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s\Settings]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s\Settings\CAM]
"EnableALPEDisableHotplug"=dword:00000000
"EnableCCC"=dword:00000000
"CCCTimeoutValue"=dword:0000000a
"CCCCompletionValue"=dword:00000020
"NCQEnableDiskIDBits"=dword:ffffffff
"EnableHIPM"=dword:00000000
"EnableDIPM"=dword:00000000
"EnableHDDParking"=dword:00000001
"CAMTimeOutValue"=dword:00000005
"EnableAN"=dword:00000001
"EnableAPS"=dword:00000000
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\ahcix64s\Enum]
"0"="PCI\\VEN_1002&DEV_4393&SUBSYS_43931849\\3&13c0b0c5&0&FA"
"Count"=dword:00000001
"NextInstance"=dword:00000001

answered Sep 24, 2012 at 4:24

How to convert an existing Windows 7 installation from IDE to RAID

I have successfully converted a pre-existing Windows 7 IDE installation to a RAID 0 configuration. It was actually not that difficult. I read hundreds of posts on multiple forums and was never able to find a solution, so I figured it out myself. Below are the steps to accomplish the task. Note: If your current OS hard drive will be used in the RAID array, you must first clone your operating system partition to a hard drive that will not be used in the RAID array.

1. Prerequisites: You must have the hard drives you will be using in your RAID, a different hard drive with your current Windows 7 installation, and an external hard drive for an OS image (DVDs or Blu-Rays would work, but much more time consuming).

2. In the Windows start menu search box type «regedit» (without the quotes) then right click the entry and click «Run as Administrator» then enter your user credentials for the UAC prompt then click yes to open regedit.

3. In regedit navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\msahci, in the right pane right click «start» then click «modify»

4. In the window that opens change the hexadecimal value to «0» and click OK. Close regedit click «File» at the top left and click «Exit».

5. Restart your computer. Enter the BIOS and change your SATA configuration to AHCI. Save settings and exit BIOS.

6. When the computer boots up, Windows 7 will install the AHCI drivers automatically. A prompt will tell you that your computer needs to restart.

7. Restart your computer. After booting up you should receive no hardware installation prompts. If you do, restart again.

8. Once there are no hardware installation prompts or restart notifications. Shut down your computer.

9. Most motherboards and RAID cards have an option to run specific SATA ports as IDE in RAID mode.

10. Verify/Connect your hard drive to a SATA RAID port that supports IDE (refer to your BIOS or motherboard manual to determine port, on my board it was SATA 5 & 6).

11. Power on your system, enter the BIOS, and change SATA operation to RAID, but change the mode to IDE (RAID is turned on, but will be running in IDE mode on the specified ports). Save BIOS settings and exit.

12. Boot into Windows 7 and you should be prompted to restart. Restart your computer.

13. You should now have a RAID controller that requires drivers. Install your RAID drivers. Restart computer.

14. Verify that your computer boots up and all hardware is installed and there are no prompts to restart. If asked to restart again, restart computer.

15. Check the device manager and verify that everything is installed properly and functioning. Shut down the computer.

16. Connect your OS hard drive to a different SATA port not assigned to the RAID. Connect the hard drives you want to use in the RAID to the proper SATA ports (I set up a RAID 0 with two identical 1 terabyte drives on SATA ports 5 & 6).

17. Power on computer and enter the BIOS. Go to SATA operation and change the mode from IDE to RAID (Should now have RAID enabled and mode set to RAID). Save changes and exit BIOS.

18. During boot up, press the key combination to enter the RAID configuration utility (mine was Ctrl-F). Create your RAID. Save changes and exit.

19. Boot up to Windows and, using Windows Disk Management (right click Computer and choose Manage, then click Disk Management), initialize the drive and partition/format if desired/required.

20. If the OS or RAID drives contain multiple partitions, go to the next step. If cloning drive follow this step and skip the next step.
    Using your favorite image creating software (I use Acronis or Ghost), clone the OS drive to the RAID drive. This can be tricky if there are multiple partitions on the OS drive or the RAID drive. If the OS drive and RAID drive both utilize a single partition, cloning is the best option. After cloning drive, reboot computer.

21. Skip this step if you cloned the OS drive to the RAID drive.
    Using your favorite image creating software (I use Acronis or Ghost), create an image of your Windows 7 partition and restore the image to the desired partition on your newly created RAID. Reboot computer.

22. Enter your system BIOS and change your hard drive boot priority to start with your RAID drive. Save changes and exit BIOS.

23. Boot in to Windows and verify that the RAID drive is now your C:\ drive. Using Windows Disk Management, re-partition/format original OS drive, or if no longer needed in system, shut down computer and disconnect original OS drive.

24. If all went well, you should now be running Windows 7 on your newly created RAID drive and your original OS drive is either blank and available as a backup/storage drive or no longer installed in the computer.

answered Nov 1, 2012 at 18:55

answered Aug 17, 2016 at 0:15

Re-install is never an option!

Hey buddy — I just pretty much went through this exact scenario except I have taken 2 x RAID 0 disks from failed external Lacie drive and have plugged them into my desktop hoping to salvage my data.

Since your system disk will not be RAID, you need to move the drive you are booting from OFF of the ICH controller, and boot that disk on that controller in IDE mode.

So:

• System HDD, on ICH controller, in IDE mode = good (but can’t install RAID driver as device needs to be present for driver to install — STUPID Intel, but I’m sure there is a technical reason for it)
• System HDD, on ICH controller, in RAID mode = bsod (can’t boot as windows doesnt have RAID driver, catch 22 really)
• System HDD, on OTHER controller, in IDE mode and ICH controller in RAID mode = bootable, and able to install

Test successful boot once moved to OTHER controller, reboot, go into BIOS and enable RAID for the ICH controller. Since you are booting using other controller, it’s all hunky dory! Now when Windows is loaded, you can install appropriate driver package for your ICH controller.

Note that the first time I booted into Win7 with my ICH controller set to RAID, I could not successfully install driver (some sort of time out) and it took a long time to shut down and eventually BSOD — a subsequent reboot and was all good.

Note for the Intel ICH controllers, recommend you use Intel Rapid Storage Technology package which includes appropriate 32/64bit drivers as well as the Intel Rapid Storage Technology utility to configure your RAID volumes (basically same as CTRL-I during POST). It took me a fair bit of Googling to decode Intel’s crazy package/release system and it seems their storage controller chipset line went though a rename at some stage. I recommend using this package which was released 23 Mar 2010.

Once you see a RAID controller in device manager, you are hot to trot. Plug your RAID disks into appropriate ports on mobo, and away you go.

Only downside about this config: usually the other controller is slower than the ICH and is built for some other task. My board (ASUS p5q3) has both JMicron JMB322 and ICH10R. I have not done any benchmarking, but from what I have researched…

Anyway, here are some helpful links I found when researching this problem:

• How to enable AHCI/RAID mode without reinstalling windows (P35/ICH9/ICH9R)
• Setting up Raid problems, help, pics

Most easy way to install drivers to offline target OS is the following:

1) Download and burn live WinPE image…
2) Boot with this image and install drivers to view your RAID partitions.
3) Run program InfToReg.. Open inf file of your RAID drivers in this program and save .reg file. Copy inf and sys files (select checkbox and specify correct path to target offline Windows). Or you can copy inf and sys files manually.
4) Open Regedit (target offline OS) and do Import of reg file.
5) Reboot…

All of that is available in Multiboot 2k10 ISO. But some programs are not in English.

P.S. Just tried it on SB950 RAID. All was done seamlessly…

answered Mar 14, 2017 at 2:06

answered Sep 3, 2015 at 14:35

VIA SATA RAID Controller

Windows 2000, 2003, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit

VIA SATA RAID Controller

Windows 2000, XP 64-bit, XP, XP 64-bit, Vista, Vista 64-bit, 7, 7 64-bit