Online rom flash component for windows

В прошлый раз мы рассматривали обновление прошивки Integrated Lights-Out 2 (iLO2) до версии 2.27 на серверах HP ProLiant DL360/380 G5 c Windows Server 2012 R2 с помощью пакета установки, распространяемого через VCRM. В конце сентября и начале октября этого года появились новые версии прошивок iLO2 а также BIOS, относящихся в частности к этому же поколению серверов. Наверно можно было бы пропустить эти обновления «мимо ушей», если бы не степень критичности уязвимостей, которые исправляются этими обновлениями.

Обновление iLO2 до версии 2.29

Относительно iLO информацию о проблемных версиях прошивок можно найти в бюллетене безопасности HP — ID c04486432 — HPSBHF03151 rev.4 — HP Integrated Lights-Out 2 and 4 (iLO 2, iLO 4), Chassis Management (iLO CM) on Proliant, Remote Denial of Service, Execution of Code, Elevation of Privilege. Как видно из этого документа, проблема безопасности распространяется в том числе и на рассмотренную нами в прошлый раз версию прошивки 2.27 для iLO2. Поэтому нам обязательно нужно выполнить обновление прошивки. Причём обновляться нужно не на следующую версию 2.28, которая имеет уже известные проблемы с JRE, описанные в документе ID c04818378 — Advisory: HP Integrated Lights-Out 2 (iLO 2) — Unable to Launch Java Remote Console with Java Runtime Environment (JRE) Versions 7 and 8 when TLSv1.1 and TLSv1.2 Are Enabled. Поэтому обновляться будем сразу на текущую версию 2.29, с момента выхода которой прошло уже достаточно времени.

FIXES:
- The Java IRC will not start when JRE versions 7 or 8 are installed and TLS 1.1/1.2 is enabled.
- Addressed the vulnerability mentioned in CVE-2015-4000 and SSRT102268 (client-side SSL/TLS connections).

Как и раньше, новую версию прошивки можно загрузить с сайта HP по ссылке: http://www.hpe.com/support/ilo2.

По указанной ссылке откроется страница загрузки HP Integrated Lights-Out 2 (iLO 2) Firmware for ProLiant G6 Servers, где выберем любую наиболее подходящую нам ОС, например Microsoft Windows Server 2008 R2 и загрузим установочный пакет версии 2.29 – файл cp027873.exe.

Ранее описанным способом копируем файл в репозитарий VCRM (хотя если ваш VCRM настроен на автоматическое обновление, то такой файл там скорее всего уже есть) и редактируем через несколько минут появляющийся файл cp027873.mnf, добавляя поддержку Windows Server 2012 R2.

Обновление BIOS до версии 2015.08.16

Не смотря на то, что фактически поддержка систем HP ProLiant DL360/380 G5 со стороны HP уже давно закончилась, а последнее обновление BIOS было в 2011 году, HP выпустили ряд обновлений прошивок для систем использующих процессоры серий Intel Xeon 5200 и 5400. Как я понял, на конференции по безопасности Black Hat USA 2015 миру была продемонстрирована уязвимость в указанной серии процессоров, после чего уважающие себя производители систем использующих эти процессоры, инициировали обновление прошивок своих материнских плат. Описание к релизу 2015.08.16:

Problems Fixed: 
While HP ProLiant servers using impacted Intel processors are not vulnerable to the specific attack announced publicly at the Blackhat USA 2015 security conference, this BIOS update includes updated microcodes from Intel which prevent the possibility of exploiting the processor vulnerability that make the attack possible with Intel Xeon 5200-series and Intel Xeon 5400-series processors. This Intel processor vulnerability is NOT unique to HP ProLiant servers.

То есть фактически это не проблема конкретных моделей серверов HP, а проблема процессоров Intel, поэтому необходимость установки данного обновления зависит от используемых у вас процессоров. В моём случае как раз имеются системы HP ProLiant DL360/380 G5 с процессорами Xeon 5200/5400 поэтому для их обновления требуется загрузка пакетов:

Online ROM Flash Component for Windows — HP ProLiant DL380 G5 (P56) Servers — 2015.08.16 (30 сен 2015) – файл cp028095.exe
Online ROM Flash Component for Windows — HP ProLiant DL360 G5 (P58) Servers — 2015.08.16 (30 сен 2015) – файл cp028101.exe

Ранее описанным способом копируем файлы cp028095.exe и cp028101.exe в репозитарий VCRM (хотя если ваш VCRM настроен на автоматическое обновление, то такой файл там скорее всего уже есть) и редактируем через несколько минут появляющиеся файлы cp028095.mnf и cp028101.mnf, добавляя поддержку Windows Server 2012 R2.

После этого обновим на агенте VCA информацию по ссылке refresh inventory и убедимся в том, что теперь теперь мы можем обновить наш сервер…

При выборе периода обслуживания серверов не забываем про то, что обновление BIOS потребует обязательной перезагрузки системы для вступления изменений в силу.

Источник

Thanks so much, this is a very useful resource. Everybody who like me has to search HP for firmware, then try to figure out how to extract relevant files from iso-scexe-whatsoever strange archives, will agree 😉 I hope this effort will continue. Thanks again, Paul

Thanks! This is very helpful!

Right, i’m going to trust you and deploy your files…

Double-check it, you’ll find the files are the same… but your input made me suspicious, and I can’t find v1.95 for iLO1 on HP site… 😉

Thank you for your job, Paul!

Thanks, added to the post!

Thanks, I have updated the post.

Great site, and more useful than HP’s for drivers, any
one got any updates on ilo2 firmware for resolving the Heartbleed crash issue?

Thanks, added

Thanks a lot, I was searching the update of iLO1. Too hard. 🙂

HP released ILO-3 1.80

Try flipping the options around

load /map1/firmware1 -source http://212.47.194.14/downloads/ilo2_225.bin

ran into a issue that the blade needed to be fully power cycled before doing the firmware update.
— CUT —
status=2
status_tag=COMMAND PROCESSING FAILED
error_tag=COMMAND ERROR-UNSPECIFIED
Invalid property value.
— CUT —

from the OA unit

OA-xxxxx> reset server 16

Successfully reset the E-Fuse for device bay 16.

(waited for the unit 2 power cycle and then did the ilo upgrade)

Great resource! Thank you so much!

Excellent site! I found in seconds for my ML350 what took ages in HP-site. Updating now 🙂

Спасибо, добвил, а также ILO2 2.27 и ILO 1.96

Thank you so much!!! Awesome stuff. Saved me clicking and clicking and clicking on HP website

guy this was very helpfull thanks

Very helpful thanks. Why can’t HP list the firmware like this. So much easier

Thanks, updated!

Thank you for making this, HP has made it as difficult as they possibly can to update ILO…

This link no longer works.

Hi, thanks, but I have this version included on top of the page already.

Thanks!
HP’s web is a … xxxxx
This made my ILO2 upgrade more convenient (though I had to usae Putty to do it!)

Thanks for this.

It seems that iLO4_2.20 has been withdrawn by HP, to be replaced by iLO4_2.22 (not released yet). At current HP’s recommended version is iLO4_2.10.

Hi, I can still see 2.20 on HP website for iLO 4.

At the moment these seem to be the latest.

ilo2_228.bin
ilo4_222.bin

Added, thanks!

Finding ILO Download on HP Websites is a bad joke…
This page helps so much, thank you!

Thank you for your effort.

There are new releases available since October 1st:

ilo2 — 2.27
ilo3 — 1.85 (not changed)
ilo4 — 2.30

Updated the page! (was on vacation, sorry for delay)

Updated the page with latest firmware, thanks for info!

Added, thanks!

Excellent article, thanks a lot and thank you for keeping it up to date.

Added, thanks!

thank you so much…crappy HP site,…this helps!! thanks again!

Thank you so much! You site is better than ugly and stupid HP

Thank you!! Worked like a charm!!

This is so convenient. Rather than navigating HP’s awful site, all the iLO firmwares are in one easy to use spot.

Added, thanks

Added, thanks

Added, thanks

Can you add MD5 as well?

Can you please upload ILO4 latest firmware release
RHEL Version: 2.40(1 Apr 2016)

Added!
- What’s the source of the 2.40 Version?
  Will this be released to the public on 01.04.2016?
  - - Any idea on where the Windows version is located?
    - Thank you Very much.. I could download the 2.40 version for ILO4 now. I follow this link regularly. this is much handy instead of searching in HP site.

Excellent!

Thank you very much indeed! I had spent about an hour on official HP website but have not managed to find iLo 4 firmware BIN file

Life saver.

Really nice version, many thanks

Obrigado ….

Me ajudou muito por aqui.

Best ILO download website ever!!!!

Thank you so much. Unbelieveable how complicated HP make it to find these.

Updated the page, thanks!

Thank you!

thank you very much…

this may not be the greatest ILO page in the world, but it IS a tribute

I dont get it my iLO2 wont update to the latest firmware
HP ML310 G4
iLO2

Trying with different browser (IE for example) can help.

Thanks you Thank you Thank you
HP website is painful, I have was digging for hours and non of the firmwere I downloaded from HP website is not working

YOU ARE THE BEST

ILO 4 version 2.44 is out according to HPE’s alerts but 7-zip tells me it won’t open the scexe file. Why can’t HP just provide a bin file?? So annoying.

try the link from the top, I was able to extract it with 7-zip without any problems

There’s no windows way to get the bin file??

I downloaded the Windows Server 2012 R2 version and extracted the bin file from the cp30136.exe file. Now I have an ilo4_244.bin file that I can install.

firmware iLO4 v2.44 is now added to the post

Added!

Thanks, added!

Thanks a lot, added to the post!

Hi,

Where did you find .bin file in HP site for firmware ilO4 2.44? Can you post official link pls?

Thanks

I’ve literally been using this page as a sysadmin for about 5 years!

The best single source of iLO .bins/info and the HP website is a complete sh*tshow to navigate at the best of times.

Bravo sir, keep up the good work.

Thank you! I am glad to help fellow sysadmins 🙂

This is a great resource; HPE is absolutely making it more and more difficult to be their customer with failing web site; failing Intelligent Provisioning firmware updates and failing ftp site. Thank you for putting this together!

Thanks, added!

Hi BackTrack,

I used to maintain my own list of firmware versions by simply mirroring from http://ftp.hp.com, but with the hp/hpe split it looks like http://ftp.hp.com isn’t updated anymore. Do you know of an automatable/scrapable way of grabbing the firmware urls?

I have never parsed hp’s ftp server, as source for updates I use either HP website or user reports or
https://github.com/seveas/python-hpilo

*EDIT*
Haha! I just realised that it is your Git repository I used before 😀
Great to finally meet you.

Thank you very much for this. HP don’t even provide bin file anymore.

Can you add the ilo files for integrity sistems? (HP rx3600…)

Great job!

I can add them, if you point me to product page.

Thanks for continuing to update this!

iLO 2.53 came out in May.

Hi there! Seems a new HP iLO 4 version is out (2.53).

An ILO 2.53 is out. I learned of it through an HPE server product bulletin/update.

Also an ILO4 2.54 is out. Please be aware that this version does a callback with HPE to check your ILO advanced key. If you ‘borrowed’ your key from somewhere else, your key might be stripped and the ilo will be reset to factory defaults. All ILO usernames will be removed and the Administrator account will be reset to its defaults too.

Did anyone else notice this?

Will it be possible to downgrade, and re-add a borrowed key?

thanks very much! HPE websites are some of the worst ones

Thx for this Page. very helpful.
Greatings from Germany

ILO 2.54 is out

Added versions 2.53 and 2.54, sorry for delay

Hello, would anyone happen to know when ilo 4 — 2.55 is out ? Apparently it fixes a lot of issues with blades being managed in OneView 3.x Thanks

Its out now.

hello o want to update ilo3 on dl380 g7 to the latest version but because my ilo version is 1.15 i cant do it . i understand that i need to install 1.20 first and then the latest one . but nowhere even here i couldnt find ilo 3 1.20 . can you please help me ?

Thank you so much for keeping this site updated, really appreciate it.

Latest iLO 4 is now 2.55 (as of 9-18-2017)

Hi. I get an error when I try to update our iLO 4 from version 1.22 to 2.55 : »
The last firmware update attempt was not successful. Ready for the next update.
»
Do you think I need to do an intermediate update before 2.55?
thank you,

Great, HP(E) web sux 🙁 something to find is mission impossible

Thx a much!

Thank you very much! The old HP site was bad, but the new one, and newer new one (HPE Support Center or whatever they call it now). It is almost impossible to find anything in there, no matter how much you pay them…

Thanks a lot for the link, added

great effort. thank you

Added Ilo5 version 1.17

Super COOL.Thank you very much for the firmwares!!!! It worked like charm.I was a little concerned because i have a ilo2 on a proliant dl380 g5 and not g6 but worked perfect with the latest version(2.30)!Now ilo2 works very well on Windows 10 with the ie plugin installed.Thumbs UP!

What about ilo5? Thanks!

Added!

nice work. saves a lot of time. hate hp’s website. do they try to hide files customers could need?

You get scexe_tmp20438, which you can unpack again with 7-zip.

MSA 2040 SAN firmware?

Thanks a lot!

ILO 5 added to the post, thanks!

Added, thanks!

thank you!

thanks man, nice to have a place to actually «find» the ilo update! HPE homepage sucks.

You are a Legend.

I have every type of iLO in my organisation and was so far behind on many of them.

No I am nearly up to date on all of them

This is so helpful and I cant thank you enough!!!!

I wish HP’s site was as logical as this one! Thank you for this.

Many thanks, this is the only internet place where I can found ILO 2 latest firmware.
They are disappeared from hp site, I think they must write less infringement coiright letters and better organize their downloads!

Its just a packaging change..

Thank you, updated the page

Thanks, last checked 5 days ago, it wasn’t there yet 🙂

Saved my life

Not all heroes wear capes mate! Thanks!

This article is PURE GOLD!!!!
This guy is an angel!

Save the life of my HP server lol

GREAT JOB!!!

Hi, thanks so much for the files!

I have a proliant mp10v2. I tried the latest file from ilo4 and ilo5, but after extracting using 7zip, the error says

ML10 v2 is gen 5, but all the updates fail. Is there a specific one i should update first do you know?

Thanks again for the page! So much easier than HPE.

Information
Server Name
Product Name ProLiant ML10 v2
UUID
Server Serial Number
Product ID
System ROM J10 02/02/2015
System ROM Date 02/02/2015
Backup System ROM J10 02/02/2015
Integrated Remote Console .NET Java
License Type iLO 4 Standard
iLO Firmware Version 2.30 Aug 19 2015
IP Address
iLO Hostname

I’m running windows 10 64bit btw

Thank you

WOW! I can’t even begin to thank you enough for making this information available. What the hell is wrong with HPE that they make the iLO firmware updates so impossible to find? I wasted half of my morning until I found your page. Thank you a thousand times over!

Big wet kiss on the cheek for you… been searching for this stuff for hours and was almost ready to cry.

Very handy!

added, thanks!
- Really? Its not visible in the list above…
  - What do you mean not visible:
    
    ILO2 : ilo2_233.bin (30-Mar-2018)

thanks, added!

thanks for all the latest firmwares, keep up the good work!
but having a strange issue with ilo3 1.89
uploads fine and flashes fine, but when run the web applet after downloaded,
im getting an error saying
Ignored exception: ExitException[ 3]com.sun.deploy.net.FailedDownloadException: Unable to load resource: https://192.168.133.106/html/intgapp3_231.jar

yes same here…..

Also be aware that they have the capability to lock out the firmware, & keys with an update so be careful.
seems the file is totally missing

Thank you very much for making things so clear. I really appreciate it!

Cheers mate..
This is an excellent ILO resource page..
If only HP could consolidate the ILO firmware into a single page and efficiently deliver the goods like you have done here they MAY have a complaint..
But HP can’t do what you have done..

Thank you

OH sorry another thought..
If you could house the Windows .exe versions of the firmware it would be very handy, not essential but handy

You can use .bin files extracted from linked archives on both Windows and Linux, so there is not really much point (there will be double amount of links)
- How?
  I cant find any procedure for extracting the bin files from the scexe file without using Linux..
  Maybe you can point us in the right direction?
  - - does not work.. I’ll get only a temp file when extracting.
    - That’s right, you can now unpack the temp file again and get the BIN.

The Link for Firmware ilo4_260.bin is wrong. It would be nice to correct it. Thank you very much

It already works, was a problem on HP site

Hey,
Thanks for the collection, it’s life saving to have site like that.
Question: In my environment mostly have iLO2, if I update firmware via Ilo webpage, the server require reboot or only the ilo will reboot ? The servers are production and up 24/7. they can be update without having to restart the whole server (on the fly) ?

Yes, only ILO will restart, not the server OS. You are welcome!

Lots of people, if not all, already told you: thank you for this precious and useful list.

Thank you ! This is so much better organized than HP website !

Thanks a lot for maintaining this valuable resource!

Thanks, added!

Thanks for the useful downloads . Its very helpful. Can you guide us for Active onboard Administrator upgrade firmware .I am not able to find firmware packages for this .

2.61 ?

Thanks for making this available.
You saved my bacon.

added, thanks!

Very helpful post and too bad HP harassed you on this one. Their site is very hard navigate and find simple things like ILO and BIOS updates!

Fantastic site, thank you so much!

Hi,

Any idea, how to pack it again into executable .scexe file.

Thanks,
Thiyagu

Thanks for reporting this, however I can’t find linux version of this firmware at the moment

thank you, added!

Hello,
Thanks for the files..
I’m using iLO 2 and v2.33 says that
========================
PREREQUISITE:
If the host operating system is Microsoft Windows:
— The «HP ProLiant Support Pack for Microsoft Windows Server»: version 9.10 or later
— The «HP ProLiant iLO 2 Management Controller Driver for Windows»: version 1.16.0.0 or later
NOTE: The «HP ProLiant iLO 2 Management Controller Driver for Windows» is included in the «HP ProLiant Support Pack for Microsoft Windows Server»
========================
When can I get «HP ProLiant Support Pack for Microsoft Windows Server» ..version 9.10 or later?
Currently have — iLO 2 v2.27, HP ProLiant iLO 2 Management Controller Driver for Windows Server 2012 v1.15, HP Insight Management Agents for Windows Server x64 Editions v10.20.0.0
Have an out of warranty ML350 G6..
Thanks.

There is now a newer iLO3 FW version: v1.91!

Thanks, added

Today new v3 iLO file was named cp037907.exe, in your link it was cp037906.exe, now it’s cp037908.exe and no download again. They are fixing something rapidly…

Привет! Current link is working ~50% of the time, if you get 404 just try again. I will update this link in a few days when this madness stops.

Thank you, updated!

Amazing job!
Really helpful! Even for an HPE employee!!!

Made my day, Let me know if HP would like to buy me a beer 🙂

Excellent. Thanks a lot for keeping this page running!

FYI iLO5 v1.40 is out

thanks man

Another huge thank you for maintaining these links. The HP ‘support’ website is a horrible maze of twisty links, all alike, and I think I saw a grue around the search button…

How can I upgrade the firmware if the server does not boot? Stops at error 270 and will not let go.
F10 does not appear.

Thanks

Perfect website.Save me lot of time clicking via that crazyness at HP.

Finding this page was a massive time saver for me… Clicking through the HP website to find the right firmware seemed almost impossible, and then I found this page.
Amazing, thank you!

thanks, added!

ilo 2.6.2 is out

Hello, I need this fil for HP Prolaint dl580 gen 9 — firmware-system-u17-2.70_2018_12_29-1.1.i386.rpm (5.6 MB)
where can I find one firmware. Now I have a version 2,30 its making me crazy.

thank you

Much thanks! I’m signed up for the HP alerts, but those alerts tend to not be very timely.

Greetings!

Great thanks for firmaware!

thanks, but I don’t see any download links yet..

New ILO 4 version released — thanks for maintaining this site, the old version links are invaluable.

Please provide dl link as I don’t see it on hp website yet
- - thanks, added!

is it save from iLO 4 Firmware version 1.32 to upgrade for 2.62 ?

or it must be upgrade for example version 2.1 first or what?

then is it OS on the server must be restart when flashing iLO upgrade ? because it is production server i scared if something gone wrong .

please help me, thanks

OMG!! Thank you so much! I lost several hours in trying to find iLO2 fw for an old HP server!

You’re a life saver!

Thank you for this very usefull site. Saved me a lot of searching.

thanks, still throwing 404 for me as well
- FYI: all download links now appear to be functional
  - thanks, updated

thanks, download links do not work currently, will update the page as soon as it’s fixed

thanks, download link doesn’t work currently, will update the page as soon as it’s fixed

Thanks a lot, highly appreciated!!!

Thank you

Thank you! Thank you! Thank you! Thank you!

Thanks, post updated

ILO2 2.33 doesn’t work with the c7000 OA with KVM firmware 4.xx. It gives error 0x4 when attempting to connect with the local KVM console. 2.32 works fine.

Tested with OA firmware 4.23 and 4.90 and BL460c G1, BL260 G5 and BL460 G6 blades using the latest blade firmware.

give me your btc address i want to donate a little bit

Thanks! 1EEosE9pxbLQzKj91EZVgJ7fX5bdE7eoXa
- sent a few satoshis
  - wow, thank you so much, was pretty sure it was a prank 🙂

Thank you very much. It was very easy to upgrade from iLO itself.

this site is much more useful than hpe.
Thx

I agree. The HPE site is probably the most difficult site to find anything on that I’ve ever encountered — no apparent logic to anything, links often change, files vanish, and all those meaningless, cryptic filenames! I hate it!

Thank you so much! I was fighting for hours against the HPE website for this file. 😉

Thank you for This , really makes things a lot easier.

Great resource. Trying to find these myself on the HP website is an exercise in frustration. You just saved me a lot of time.

Much appreciated for these firmware updates! Made updating my server so much easier, since I had bought it from a seller online, it didn’t come with a warranty or any of the licenses. Now, hopefully my fans can stop running at 94% and hopefully go down to about 10-20%.

Thanks!

Thanks, added!
- - The only difference I see is the filename, cp041711.exe contains ilo5_210_SHA512.bin, probably newer installer.
    Ilo version is identical, as well as build time (30.10.2019).
    - Thanks!

Anyone else getting the following error while updating iLO5 to 2.10?
«The last attempt to update or upload firmware was not successful. Make sure you are using a valid, signed flash file and try again.»

- - Thanks for confirming, I have replaced the link on the page

you are doing goods work!

Just a thank you for that work, great help found here

A great resource as always! Just spotted there’s a new firmware versino for iLO5 — now updated to 2.12

Links updated, thanks!

Added, thanks!
- Not working links 🙁
  
  This page isn’t workingdownloads.hpe.com didn’t send any data.
  ERR_EMPTY_RESPONSE
  - Lol, HP downloads website has expired https cert 🙂
    If you confirm security exception, you will be able to download

ILO4 : ilo4_273.bin (iLO4 v 2.73.2 11-Feb-2020)
Redirects to: CP042663.scexe while the latest ilo4_273.bin is CP042664

Am I mistaken, or is this newer or different?

CP042663 — linux package
CP042664 — windows package
firmware inside is exactly the same:
iLO4 v 2.73.2 11-Feb-2020

Thanks !!!

thx man good library site, hp site is sh!t

thanks a lot 😉

Good job you did there!

Can I update a Hpe ML10 Gen 9 with ILO3 to ILO4

Are you sure you have a Gen9? From the specs, the Gen9 doesn’t use an iLO, it uses some kind of Intel chipset management solution.

— ProLiant ML10 Gen9 Server specs:

https://h20195.www2.hpe.com/v2/gethtml.aspx?docname=c04922941

>> On System Management Chipset

>> Intel® Active Management Technology (Intel® AMT 11.0)

>> NOTE: The server supports the Intel Standard Manageability when the Intel Pentium or Core i3 processor is installed. The server supports Intel AMT when the Intel Xeon processor is installed in the system

If you’ve got just the ProLiant ML10, then it has an iLO3 according to the specs.

— ProLiant ML10 Server specs:

https://h20195.www2.hpe.com/v2/gethtml.aspx?docname=c04111408

If you’ve got the ProLiant ML10 v2, the specs say it has an iLO4:

— ProLiant ML10 v2 Server specs:

https://h20195.www2.hpe.com/v2/gethtml.aspx?docname=c04567801

If you’ve got the ProLiant ML10 Server with an iLO3, there wouldn’t seem to be an upgrade path to a v2 (that has the iLO4) without a complete system swap, at least as far as I can tell…

Still pointing straight out to the firmwares you need. Still beating the HPE search bar…
thnx! Safes a lot of time, finding the old FW’s.

Thank you!

Thanks, added

Added, thanks

Added, thanks

You don’t have to type «chmod 755», you can do «chmod +x» to only change the executable bit. This will prevent mishaps if you fat finger like I do.

I agree, fixed, thanks
Actually, you don’t need to chmod at all. It’s a shell script so ‘sh ./CP022551.scexe —unpack=/tmp/iLO3’ works as well.

ilo4 v2.75 and ilo3 v1.93 have been released.

ILO5 v2.30 is out

thanks, added

cp045313.scexe is correct file name, in case you want to check.
I also checked the version of the ilo4.bin file, it’s still ilo4_275.bin (13 Aug 2020)

The Fixes sections on the website says:
iLO 4 version 2.75(b) was released with a packaging update. The update does not affect the firmware functionality. If version 2.75 was previously deployed to target device, then it is not necessary to update to version 2.75(b)

Potential Ripple20 vulnerabilities affecting the TCP/IP stack.

ilo5 updates:

2.30 (4 Sep 2020)
2.19 (18 Aug 2020)

Thanks, added. I don’t see Linux version of 2.19 firmware on HPE website, it seems to affect only esx/vsphere

what’s the difference between versions 2.75( a) and 2.75 (b)?

binary firmware files are identical in both versions:
iLO 4 version 2.75(b) was released with a packaging update. The update does not affect the firmware functionality. If version 2.75 was previously deployed to target device, then it is not necessary to update to version 2.75(b)

Thank you for this information, I couldn’t find Linux firmware version on HPE website, hope it will be fixed in a more recent release.

Thank you for providing this service to the HPE Community.

No problem, feel free to make a donation XD
- Wow, thanks a lot, that’s second donation I received this year.

Latest on the Vmware problem in ILO 5 2.30
«Yes, we are making a short term fix in iLO 5 v2.31 as we work through the final solution with VMware. Will update once we get iLO 5 v2.31 released.»

When is the 2.31 version expected to be released? Do you know that?

And so the latest ilo 5 version 2.31 is here.
With the fix for vmware

thanks, added

Thank you!

Thanks, there is no Linux version of ILO 4 2.76 package for some reason, will wait a bit
- - Thank you, added!

Just what I needed today, thanks for this!

added, thanks

thanks, updated

Please make it clear at the top of the page that these images are for the HP ProLiant ILO series only. HP Integrity servers also have ILO and ILO2, but the Integrity ILO images are incompatible with the ProLiant ILO images. Otherwise a great page of ILO image links!

Good night, I have an ML150 Gen9 with an expired warranty contract and I need to update the BIOS, mine is version 2.60 (P95) does anyone have above it to update? I need to install windows server 2016 or 2019.

You still have the possiblity to download online rom flash from support.hpe.com
with a valid registration but expired warranty contract.
- this option not working

is there any way to possibly enhance this list further by keeping up two more columns for the actual iLOx ‘Version’ & ‘Release Date’ ?

Merci beaucoup !

FYI ILO5 is now to 2.41

thanks, added

Hi, i have an Micorserver Gen8 with the iLO 4 2.73, but i need the 2.74 firmware update file.

Current ILO5 Version is 2.42. The corresponding package is cp046458 which is currently only included in SPP 2020-10-04.

FILE NAME: iLO5_242.bin
TITLE: iLO 5 firmware v2.42
BUILD DATE: April 5, 2021
EFFECTIVE DATE: April 8, 2021

Did you notice that as part of the latest SPP for Gen10 a version 2.42 of the firmware for iLO 5 is included (cp046458.exe)?
The only way I can find to download the file is by downloading the SPP.

iLO 4 V 2.78 and iLO5 V 2.44 are already available.

Thanks for this archive, much appreciated!

Hi,

This version ‘ilo3_193.bin’ is also compatible with VMWARE (ESXi) 6.5 Operating System or only Linux ?

Thank you for your response.

iLO firmware (.bin file) is identical for any OS you install

Awesome archive! Makes my life so much easier 🙂

I appreciate your help for ILO, hope HP learns what is being user-friendly.

I was having an issue updating ILO2 from v1.20 to the latest since it would not work via the browser. Tried so many version and would not work, then I was able to do it via command line since the server was running RHEL 6. In case you’re having the same issue, here is what I did.
# rpm -ivh hponcfg-4.6.0-0.x86_64.rpm # Installed hponcfg
# hponcfg | grep Firmware # Check current Firmware version
Firmware Revision = 1.20 Device type = iLO 2 Driver name = hpilo
# chmod u+x CP035238.scexe # Update firmware file permission so it’s executable
# sh CP035238.scexe # Start the install
FLASH_iLO2 v1.12 for Linux (Aug 31 2009)
Copyright 2009 Hewlett-Packard Development Company, L.P.
Firmware image: ilo2_233.bin
Current iLO 2 firmware version 1.20; Serial number ILOUSE641NDNF

Component XML file: CP035238.xml
CP035238.xml reports firmware version 2.33
This operation will update the firmware on the
iLO 2 in this server with version 2.33.
Continue (y/N)?y
Current firmware is 1.20 (Jun 06 2006 15:31:37)
Firmware image is 0x300000 bytes
Committing to flash part…
******** DO NOT INTERRUPT! ********
Flashing completed!
Attempting to reset device.
Succeeded.
Waiting for iLO 2 to reboot…
iLO 2 reboot completed.

That’s it!

What is the best ilo version for Dl 385p gen 8 server. if it is currently running on ilo 3.

ilo5 v2.46 available

Thanks, added 2.46 for windows and 2.48 for linux

TY, added

iLO5 v2.55 is now available

added, thanks

lo 5 V2.55

added, thanks

Hello!! Thank you so much for all the work you have done getting and uploading the files. I wanted to know, I have a HP Proliant ML10 V2. I have searched the internet and noticed that V2 was able to update to ILO 4, but no matter what I keep getting a fail error when trying update to ILO 4. Also, I updated to 194 bin file and still can’t access my ILO 3 over all the latest browsers. I keep getting a ERR_SSL_VERSION_OR_CIPHER_MISMATCH. Im hoping that HP will do another update or maybe if i can get updated to ILO 4 then I will be able to access it via the latest browsers. Anyway, thanks in advance.

Hi Keith, I’m able to use Internet Explorer (whatever version is there on a fully patched Win10) to connect to iLO3 on DL Gen7 servers, while all other browsers fail with same ERR_SSL_VERSION_OR_CIPHER_MISMATCH error you had.
BTW I’ve never heard of being able to do just firmware update to get to newer type of ILO (ILO2 to ILO3 or ILO3 to ILO4). I believe what they might mean was a hardware upgrade option, but tbh can’t recall seeing that either.
- You can enable FIPS mode on the ILO for those cipher mismatches to be gone.

Thank you backtrack <3

ILO 2.79 for ILO4 is now available.

added, thanks

added, thanks

Does anyone know something about iLO 4 V 2.78 and problem with IML «Mark as repaired» field? Now it’s greyed out always. iLO 4 V 2.77 works just fine. Quite annoying 🙁 I have to clear IML everytime instead of marking as repaired…

thanks, added

iLO 4 2.79 is out now!

added!

thanks for reporting!

ilo4 has update, please update the table

HPE iLO 4 v2.79

done, sorry for delay

can’t thank you enough

ILO 5 V2.60 is out

thanks for reporting, added

thanks, added!

thanks, sorry for delayed update

thanks, sorry for delay

thanks, sorry for delay

thanks, windows version can be easily unpacked with 7-zip

thanks for the links, it seems the BIN files are the same as in December release

- Perfect, both are fine of course, thanks for the link 🙂

thank you

thanks for reporting!

thanks a lot for maintaining this, it is extremely useful

Just wanted to say thank you for this site. I visit this site at least once a quarter because its just so much faster to grab iLO binary from here.

Thanks again and keep it up!

You can always go to the HP site and check the checksum.
I do that often with SPPs I download from … yeah, weird pages.
Checksum matches, gtg

I can’t seem to get my iLO5 2.63 .bin file to upload; always says it fails, sometimes with a verification error. I have downloaded a couple of times on different systems; just doesn’t seem to work. Do all the extracted files from the .EXE (this is from a Windows machine) need to be in the same folder as the ilo5_263.bin file? I wonder if there is anything missing or a step I am leaving out.

Thanks in advance.

Thank you, It really is a pain that HP have a habit of re-organising their sites such that they break links.
I can usually find the firmware after several searches and the opening of several tabs, but this really makes life far easier.

Isaac

Where can i download bios for proliant dl360 gen9 P89

System ROM
P89 v2.76 (10/21/2019)

Where can i find this —> P89 v2.76 (10/21/2019) HPE blocked the BIOS downloads,

Added, thanks!

Hi there, New versions of at least ILO 4 (v2.80) and ILO 5 (2.65) are out. Thanks

Added, thanks!

Where can i download bios for proliant ML150 gen9 P95 2.92 ?
in HPE site, download is locked 🙁

Thank you for this site!!! It save my it technical live more than once !!

Thanks again and keep it up!

Jérémy!

Still doing good work after all this time. It’s impossible to find on HP crappy support website.

Thanks man!

Hi
Do you have HP Integrity iLO2 MP firmware? Seems to be different from Proliant iLO2

OK, perhaps this may come handy to someone…

We still run Gen7 blades (ProLiant BL465c G7 [half height, Linux] and ProLiant BL685c G7 [full height, MS-Win]) that use System ROM A19 and A20, respectively. I tried to update the ROM to the latest, π-day (3/14/2018), release.

There is no SPP (Service Pack for ProLiant) any more, but the ROM component can be downloaded. The respective update files are ‘CPQA1903.46E’ and ‘CPQA2003.46E’ as extracted from ‘cp036027.exe’ and ‘cp035679.exe,’ but hose cannot be installed via iLO3. The ROMpaq for Gen7 (intructions for overcoming the ‘Drive is Write Protected: https://www.icare-recovery.com/howto/hp-usb-disk-format-tool-device-media-write-protected.html ) failed with ‘Illegal OpCode’ and a Red Screen of Death, but the ROMpaq for Gen8 just needed the two files (.46E) added to the di where another ‘.46E’ already was, and the update worked.
Best of Luck to You!
AK

errata: ‘but those cannot,’ ‘added to the dir where’
π-day release mitigates the Spectre vulnerability:

>Spectre is a subset of security vulnerabilities within the class of vulnerabilities known as microarchitectural timing side-channel attacks. These affect modern microprocessors that perform branch prediction and other forms of speculation.

Thank you, added!

Thank you, added!

Great resource! thanks so much. Do you have access to system ROM BIOS .bin files (I36) for g9 blade servers?

iLO4 v 2.81 released but broken download links

For those of you who want to extract the firmware from the Linux rpm package, gnutar is able to extract all the files from the Linux download. macos version of tar seems to be gnutar and can also extract all the files. You can see below.

% tar tf firmware-ilo5-2.71-1.1.x86_64.rpm
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/.cpq_package.inc
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/.setup
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/CP052504.xml
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/LICENSE.txt
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/hpsetup
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/ilo5_271.bin
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/payload.json
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/readme.txt
./usr/lib/x86_64-linux-gnu/firmware-ilo5-2.71-1.1/setup
./usr/lib/x86_64-linux-gnu/hp-scexe-compat
./usr/lib/x86_64-linux-gnu/hp-scexe-compat/CP052504.scexe
./usr/lib/x86_64-linux-gnu/scexe-compat
./usr/lib/x86_64-linux-gnu/scexe-compat/CP052504.scexe

thanks, added!

thank you

Thank you so much!!

Quick query. I’ve obtained a ML10 v2 server from a friend, it currently has ILO4 2.10

Do you know if I’m able to go straight to 2.81 or have to perform intermediary upgrades too?

Many thanks (for the software and any potential replies)

Hi!
Thanks for your constant updates. What do you think — are updates from the vendors (HPE and other) released after February dangerous for users in Russia?

Hi,

Can you get the latest spp iso image for the dl380 g9?
Now days it getting harder to get it without a support contract.

Many thanks in advanced

Muchas gracias por compartir estos archivos tan importantes para los servidores.

Thank you, My Life saver!!

updated, ty

added, thanks

Recently ran into an issue with a new client, servers iLO firmware was ancient (ilo 5 1.40) and it can’t update directly to the latest (2.78).

luckily this site exists to get hold of 2.10 which then allowed me to jump up to the latest.

God send and bookmark’ed

Minimum firmware version for iLO5 to upgrade to the latest version is 1.48

Thank you sooo much!!!!!!!!!

Posts 317 & 318 above only have links for iLO5 2,78 for LINUX! What is the link for the Windows version for 2,78 for iLO5 ?

Thanks in advance.

Added, thanks!

LOL = Lots of Love! And my thanks for this! hp is apparently unable to make stuff findable through their own page 😀

I need source for this notifier, so I can automate updating this page 🙂

iLO 5 v2.95 was released on 21/07/2023

i can mirror this for you and im not afraid of any hatemail.
contact me

iLO 5 v2.96 is released

added, thanks

Just wanted to say that not being a sys admin with any experience of server maintenance, with your post, I managed to solve the issue of my gen8 server fans going completely bonkers (it even caused 3 fans to fail)

The update to ilo seems to have resolved this… couldn’t have done it without you… thanks

Thanks, added

Thanks a lot for your work.
This is really clean and useful!

Kudos!

Источник

HPE System Tools Library

This repository contains HPE-specific system management tools that were left out of the general purpose
System Tools Library.

Tool	Description
Get-SmartUpdateInfo.ps1	Display information about HPE Smart Updates CPnnnnnn.EXE.
GetVer.ps1	Display the versions of all HP and HPE hardware and software on the system.

All tools support the -? option for getting help.

Get-SmartUpdateInfo.ps1

Smart Updates, also known as Smart Components, are standalone executable files with firmware, driver, or software updates.
They are distributed in Service Packs for ProLiant (SPP), and more generally on the support.hpe.com web site,
in the Drivers and Software area for each product. They’re smart in the sense that they have built-in logic for
deciding if the update is necessary or not on the current system.
The smart updates for Windows have a name like cpNNNNNN.exe, with NNNNNN a unique number identifying the update.

The problem with Smart Updates is that when you have a large collection of them, as in a SPP, or maybe in a private
repository of your own, it is hard to identify which Smart Update does what. For example, in the 2016-10 SPP, the
swpackages directory contains 858 such cp*.exe files.

Get-SmartUpdateInfo.ps1 is a PowerShell script that extracts the built-in XML meta data of cp*.exe files, and displays
it as standard PowerShell lists or tables. This allows to use all the formidable formating and filtering abilities
of PowerShell to find the Smart Update you need.

Example displaying the properties for one update:

Get-SmartUpdateInfo.ps1 cp040096.exe
Get-SmartUpdateInfo.ps1 cp040096.exe | fl *

Output:

PS F:\Library\Firmware\bios> Get-SmartUpdateInfo.ps1 cp040096.exe

Name     Content                                                                            Version    Date
----     -------                                                                            -------    ----
cp040096 Online ROM Flash Component for Windows x64 - HP ProLiant DL380p Gen8 (P70) Servers 2019.05.24 2019-07-06


PS F:\Library\Firmware\bios> Get-SmartUpdateInfo.ps1 cp040096.exe | fl *


Category     : BIOS - System ROM
Description  : This component provides updated system firmware that can be installed directly on supported Operating
               Systems.  Additionally, when used in conjunction with Smart Update Manager (SUM), this Component allows
               the user to update firmware on remote servers from a central location. This remote deployment
               capability eliminates the need for the user to be physically present at the server in order to perform
               a firmware update.
FileName     : F:\Library\Firmware\bios\cp040096.exe
Version      : 2019.05.24
Content      : Online ROM Flash Component for Windows x64 - HP ProLiant DL380p Gen8 (P70) Servers
Name         : cp040096
Languages    : en
Date         : 2019-07-06
Manufacturer : Hewlett Packard Enterprise



PS F:\Library\Firmware\bios>

Examples displaying in list or table format the meta-data of all Smart Updates in the current directory:

Get-SmartUpdateInfo.ps1 cp*.exe
Get-SmartUpdateInfo.ps1 cp*.exe | fl
Get-SmartUpdateInfo.ps1 cp*.exe | ft -a

Another example using filtering to select BIOS related Smart Updates:

dir cp*.exe | Get-SmartUpdateInfo.ps1 | where {$_.category -like "BIOS*"}

This will output something like:

Name     Content
----     -------
cp033181 Online ROM Flash Component for Windows x64 - HPE Apollo 4510 Gen10/HPE ProLiant XL450 Gen10 (U40) Servers
cp033389 Online ROM Flash Component for Windows x64 - HPE ProLiant ML110 Gen10 (U33) Servers
cp033393 Online ROM Flash Component for Windows x64 - HPE Apollo 2000 Gen10/HPE ProLiant XL170r/XL190r Gen10 (U38) S...
etc...

It is then easy to find the exact one you need.

GetVer.ps1

This script displays the versions of all HP and HPE hardware and software on the system.
The output is formatted in an easy to read structured format called SML.
To further process the output, use the -xml option, to output the same data formatted as XML instead.

Sample output:

computer {
  model  "HP X5460sb G2 Ntwk Stor Blade"
  sku    706900
  name   idpk1
  domain lab.gre.hp.com
  bay    1
  bios   I27
  date   2018-02-22
}
ilo {
  model "Integrated Lights Out 3 (iLO3)"
  name  idpk1-ilo
  ip    10.16.129.37
  fw    1.92
  date  2020-04-22
}
pmc {
  model "PowerPIC G2 Ntwk Stor Blade"
  fw    1.6
}
enclosure {
  model "HP 16LFF BACKPLANE      "
  name  idpk-em
  ip    10.16.129.13
  fw    1.50
  date  2014-08-04
  svn   20535
}
scsi {
  p410i {
    model "Smart Array P410i"
    fw    6.64
  }
  1210m {
    model "Storage Works 1210m Controller"
    fw    1.78
    build 2013071101
    date  2013-07-11
    cpld  0xc
  }
}
disks {
  disk1 {
    model "HP      EG0300FAWHV"
    fw    HPDD
  }
  disk2 {
    model "HP      EG0300FBDBR"
    fw    HPDA
  }
}
seps {
  ee {
    model "EE 999999"
    fw    1.8.0.28
  }
  ie {
    model "IE 999999"
    fw    1.8.0.28
  }
  ee {
    model "EE 999999"
    fw    1.8.0.28
  }
  ie {
    model "IE 999999"
    fw    1.8.0.28
  }
}
lan {
  nc382m {
    model "HP NC382m DP 1GbE Multifunction BL-c Adapter"
    fw    5.2.3
  }
  nc553i {
    model "HP NC553i Dual Port FlexFabric 10Gb Converged Network Adapter"
    fw    11.1.183.23
  }
  nc365t {
    model "HP NC365T PCIe Quad Port Gigabit Server Adapter"
  }
}
software {
  image   name="HP StoreEasy Quick Restore DVD" 4.01.0a.22
  sr      name="HP StoreEasy Service Release" 2017.05.5
  windows name="Windows Storage Server 2012 R2 Standard (en-US)" 6.3.9600
  program name="HP Storage Cluster Configuration Utility" cmd="ccu" 2.5.12539
  program name="HP Storage SW and FW Versions List Tool" cmd="getver" 2015.10.09.1468
  program name="Alert_Email_Provider" 1.0.0
  program name="AlertEmail" 1.0.0
  program name="EMIPMonitor" 1.3.0
  program name="Hewlett-Packard CMP" 2.00.15013
  program name="Hewlett-Packard CMP - Firmware Module" 2.00.22333
  program name="HP Array Configuration Utility (64-bit)" 9.40.12.0
  program name="HP Array Configuration Utility CLI (64-bit)" 9.40.12.0
  program name="HP CMP Hardware Diagnostics tool" 1.0.3
  program name="HP DAN Cluster API" 2.5.12539
  program name="HP Insight Management CSP WBEM Providers for Windows" 3.0.0.3
  program name="HP Lights-Out Online Configuration Utility" 4.8.0.0
  program name="HP Management Web Services" 1.1.0.220
  program name="HP NAS Online Help" 1.4.0
  program name="HP Pool Manager Provider" 1.1.0000
  program name="HP ProLiant Health Monitor Service (X64)" 3.20.0.0
  program name="HP ProLiant iLO 3 WHEA Driver (X64)" 3.0.0.0
  program name="HP ProLiant iLO 3/4 Channel Interface Driver" 3.10.0.0
  program name="HP ProLiant iLO 3/4 Management Controller Package" 3.20.0.0
  program name="HP ProLiant iLO CHIF Driver (X64)" 3.10.0.0
  program name="HP ProLiant iLO Core Driver (X64)" 3.9.0.0
  program name="HP RemoteSync Service" 1.5.0
  program name="HP Server Manager Extensions" 1.1.0.11
  program name="HP Smart Array SAS/SATA Event Notification Service" 6.46.0.64
  program name="HP Smart Storage Administrator" 2.40.13.0
  program name="HP Smart Storage Administrator CLI" 2.40.13.0
  program name="HP Storage Viewer" 1.3.0
  program name="HP StoreEasy 5000 Firmware Update Package" 001.008.1503.21
  program name="HP StoreEasy 5000 Firmware Update Package" 001.008.1503.21
  program name="HP StoreEasy 5530 Enclosure Manager Settings" 1.3.0
  program name="HP StoreEasy ICT" 3.0.1
  program name="HP StoreEasy PoolManager" 1.1.0.178
  program name="HP StoreEasy Storage Management Provider" 1.1.0
  program name="HP Version Control Agent" 7.2.0.0
  program name="HPE Insight Management Agents" 10.60.0.0
  program name="HPE Insight Management WBEM Providers" 10.60.0.0
  program name="HPE Insight Management WBEM Providers for Windows Server x64 Editions" 10.60.0.0
  program name="HPE System Management Homepage" 7.6.0
  program name="HPWitnessDisk " 1.0.0
}

Источник

Содержание:

- 0.0.1 Войти

1 * RECOMMENDED * Online ROM Flash Component for Windows x64 — HP ProLiant DL360 G5 (P58) Server
2 Описание
3 Инструкции по установке
4 Замечания о версии
5 Исправления

Когда новую ОС Windows Server 2012 загоняли на виртуальные машины на базе Hyper-V 2.0 всё казалось радужно и приятно, однако когда дело дошло до установки на аппаратную платформу “не первой свежести” — HP ProLiant DL 360/380 G5 – веселье куда-то улетучилось… После изучения ситуации с драйверами HP для новой ОС поймал себя на мысли, что любимый вендор ведёт себя как закадычный друг, то есть друг, который хочет взять своих клиентов за кадык, внушая им то, что работать с новой ОС можно только на серверах поколения G7/G8…

Здесь изложена небольшая история о, том как я бодался с имеющимся на сегодня комплектом драйверов и прошивок для серверов ProLiant – HP Service Pack for Proliant (SPP) версии 2012.10.0

Итак, скачав с сайта HP доступный на данный момент файл HP_Service_Pack_for_Proliant_2012.10.0-0_713293-001_spp_2012.10.0-SPP2012100.2012_1005.37.iso размером 2 513 903 616 байт, копируем его на сервер со свежеустановленной Windows Server 2012 и с помощью новой встроенной функции Windows монтируем образ в виртуальный DVD-привод …

Перед непосредственным запуском программы устанавливаем в системе службу SNMP Service (в случае если не планируется использовать WBEM).

Далее, открываем командную строку с правами администратора и из смонтированного образа SPP запускаем программу установки hpswpackageshpsum.exe
В конфигурации по умолчанию предлагаемый SPP список репозитариев выглядит так

В такой конфигурации, дойдя до шага непосредственной установки мы столкнёмся с ошибками зависимостей из-за того, что текущая версия SPP не может определить для некоторых устройств подходящий драйвер. Конкретно в моей ситуации при запуске SPP на платформе ProLiant DL 360 G5 возникла проблема с распознанием iLO2 и Smart Array P400i

В поисках решения проблемы на странице HP ProLiant Servers — Microsoft® Windows Server® 2012 обнаружил ссылку указывающую на дополнение к SPP для поддержки Windows Server 2012 — Supplement for SPP . Это дополнение называется Microsoft Windows Server 2012 Supplement for HP Service Pack for ProLiant и представляет собой архивный файл MSsupplement2012.exe размером 183 713 504 байт, который после загрузки был распакован во временный каталог на подопытном сервере.

При повторном запуске SPP добавил этот каталог как дополнительный источник поиска обновлений. Для полноты эксперимента, дополнительно была включена проверка обновлений с ftp.hp.com

После того как HP Smart Update Manager прокачал с интернета дополнительно внушительную пачку обновлений и просканировал локальные каталоги…результат оказался весьма удручающим – ни пакет дополнений ни доступные на ftp файлы не решили проблему…

После некоторого количества экспериментов удалось найти работоспособный вариант мануальной установки драйверов. Выяснилось, что оба неизвестных системе устройства – Base System Device и IPMI Interface в нашем случае относятся к контроллеру iLO2.

Для устройства Base System Device подошёл драйвер HP ProLiant Integrated Lights-Out Management Interface Driver for Windows Server 2003/2008 x64 Editions версии 1.16.0.0 (файл hpswpackagescp016017.exe размером 739 096 байт из состава выше обозначенного SPP). Отдельно загрузить драйвер можно по ссылке .

Для устройства IPMI Interface подошёл драйвер HP ProLiant iLO 2 Management Controller Driver for Windows Server 2008 x64 Editions версии 1.14.0.0 (файл cp013803.exe размером 695 624 байт). На текущий момент загрузить драйвер можно по ссылке .

Для контроллера Smart Array P400i система установила драйвер который шёл в составе ОС, однако этот драйвер не позволяет полноценно обнаружить устройство утилитам HP и поэтому потребовалось заменить его на родной драйвер HP ProLiant Smart Array SAS/SATA Controller Driver for Windows Server 2012 версии 62.24.2.64 (файл hpswpackagescp018436.exe размером 717 064 байт из состава выше обозначенного SPP). Отдельно загрузить драйвер можно по ссылке .

Все указанные драйвера нужно выполнять в режиме ручной установки для каждого отдельного устройства, предварительно распаковав инсталляционный файл драйвера.

После этого установка драйверов и утилит из состава HP Service Pack for ProLiant 2012.10.0 пройдёт без проблем.

1) Ставим 2012 с графической оболочкой
2) Инсталлируем фичу: SNMP Service
3) Скачиваем SPP с сайта HP:
HP_Service_Pack_for_Proliant_2013.02.0-0 _725490-001_spp_2013.02.0-SPP2013020B.20 13_0628.2.iso
4) Качаем Microsoft Windows Server 2012 Supplement for HP Service Pack for ProLiant:
MSsupplement2012.exe
5) Распаковываем MSsupplement2012.exe в папку C:Win2012 (например).
6) Качаем HP ProLiant Integrated Lights-Out Management Interface Driver for Windows Server 2003/2008 x64 Editions:
cp016017.exe
7) Качаем HP ProLiant Smart Array SAS/SATA Controller Driver for Windows Server 2012:
cp018436.exe
Инсталлируем драйвера из п.п. 6 и 7. Если система дала отлуп «hardware not found» или «OS version not supported» — распаковываем архивы и ставим драйвера вручную через devmgmt.msc. Перезагружаем сервер, если необходимо.
9) Монтируем образ SPP (из п.3)
10) Запускаем hpswpackageshpsum.exe
11) Кроме дефолтного репозитория добавляем FTP* и папку с содержимым из MSsupplement2012.exe. Жмачим next.
12) Localhost добавляется автоматически. Добавляем другие хосты, если необходимо. Жмачим next. Смотрим, как проходит self discovery.
13) Проверяем, нет ли failed dependencies:
14.1) Если есть — проверяем, какие устройства остались из драйверов и ставим их как в п.8.
14.2) Если всё в порядке жмачим next.
15) Проверяем, всё ли ок.
16) Перезагружаем сервер.
17) PROFIT.

UPD:
* — уже давно не актуально. Адрес FTP изменился или FTP-сервер отключен насовсем.

Также, подчеркну следующее: в силу неизвестных причин (подозреваю встроенные драйвера RAID-контроллера), система устанавливается ОЧЕНЬ долго (порядка 3-х часов).
Однако, если создать виртуальную машину в hyper-v и развернуть 2012R2 в ней, то там она ставится, как положено — за 3-5 минут.

14.1) Если есть — проверяем, какие устройства остались из драйверов и ставим их как в п.8.
14.2) Если всё в порядке жмачим next.

14.3. Если эта хрень стоически не может скачать пару файлов, идем в каталог, куда оно льет, и создаем файлы пустышки с нужными именами, после чего оно сразу подобреет.

* RECOMMENDED * Online ROM Flash Component for Windows x64 — HP ProLiant DL360 G5 (P58) Server

Загрузка файла означает ваше согласие с условиями и положениями Лицензионного соглашения на программное обеспечение Hewlett Packard Enterprise.
Примечание. Для использования некоторых программ необходимо наличие действующей гарантии, контракта на поддержку с Hewlett Packard Enterprise или оплаченная лицензия.

Тип:	BIOS (Entitlement Required) — Системное ПЗУ
Версия:	2015.08.16(30 сен 2015)
Операционная система(ы):

Microsoft Windows Server 2003 for 64-bit Extended Systems

Microsoft Windows Server 2008 R2

Microsoft Windows Server 2008 x64

Имя файла:
cp028102.exe (1.2 MB)

Due to system security configuration set to «high», a supported system may experience any of the following errors when attempting to install or update the system with Online ROM Flash Component for Windows x64 — HP ProLiant DL360 G5 (P58) Server version 2011.05.02:

«This program has been blocked for your protection»
«Blocked»
«Not Trusted»
MSIExec installation error (Return code: 1625)
«The recommended software listed below could not be installed…»

To ensure the integrity of your download, HP recommends verifying your results with this MD5 Checksum value:

79552558838b4d5fa2d68616d3d91110

cp028102.exe

Reboot Requirement:
Reboot is required after installation for updates to take effect and hardware stability to be maintained.

To update firmware from Windows operating system on target server:

1. Place the Component in a temporary directory.
2. From the same directory, run the Component by double-clicking it.
3. When the Component dialog window displays, click the Install button to initiate the firmware upgrade.
4. Reboot your system if you would like the update to take effect immediately.

Supplemental updates for supported ProLiant servers and options can be done by using HP Smart Update Manager, which is found on the Service Pack for ProLiant ISO.

Place the Service Pack for ProLiant on a USB key using the USB Key Creator Utility.
Place the desired components to be updated in the directory, hpswpackages on the USB key.

Update the firmware and software in the usual manner.

This component can only be executed on Windows x64.

«This program has been blocked for your protection»
«Blocked»
«Not Trusted»
MSIExec installation error (Return code: 1625)
«The recommended software listed below could not be installed…»

Upgrade Requirement:
Recommended — HP recommends users update to this version at their earliest convenience.

HP ProLiant DL360 G5 System ROM — P58

Last Recommended or Critical Revision:

While HP ProLiant servers using impacted Intel processors are not vulnerable to the specific attack announced publicly at the Blackhat USA 2015 security conference, this BIOS update includes updated microcodes from Intel which prevent the possibility of exploiting the processor vulnerability that make the attack possible with Intel Xeon 5200-series and Intel Xeon 5400-series processors. This Intel processor vulnerability is NOT unique to HP ProLiant servers.

Upgrade Requirement:
Recommended — HP recommends users update to this version at their earliest convenience.

HP ProLiant DL360 G5 System ROM — P58

Last Recommended or Critical Revision:

Тип:	BIOS (Entitlement Required) — Системное ПЗУ
Версия:	2015.08.16(30 сен 2015)
Операционная система(ы):

Microsoft Windows Server 2003 for 64-bit Extended Systems

Microsoft Windows Server 2008 R2

Microsoft Windows Server 2008 x64

Описание

Инструкции по установке

«This program has been blocked for your protection»
«Blocked»
«Not Trusted»
MSIExec installation error (Return code: 1625)
«The recommended software listed below could not be installed…»

To ensure the integrity of your download, HP recommends verifying your results with this MD5 Checksum value:

79552558838b4d5fa2d68616d3d91110

cp028102.exe

Reboot Requirement:
Reboot is required after installation for updates to take effect and hardware stability to be maintained.

To update firmware from Windows operating system on target server:

Supplemental updates for supported ProLiant servers and options can be done by using HP Smart Update Manager, which is found on the Service Pack for ProLiant ISO.

Place the Service Pack for ProLiant on a USB key using the USB Key Creator Utility.
Place the desired components to be updated in the directory, hpswpackages on the USB key.

Update the firmware and software in the usual manner.

This component can only be executed on Windows x64.

Замечания о версии

«This program has been blocked for your protection»
«Blocked»
«Not Trusted»
MSIExec installation error (Return code: 1625)
«The recommended software listed below could not be installed…»

Upgrade Requirement:
Recommended — HP recommends users update to this version at their earliest convenience.

HP ProLiant DL360 G5 System ROM — P58

Last Recommended or Critical Revision:

Исправления

Upgrade Requirement:
Recommended — HP recommends users update to this version at their earliest convenience.

Источник

Обновление iLO2 до версии 2.29

Обновление BIOS до версии 2015.08.16

HPE System Tools Library

Get-SmartUpdateInfo.ps1

GetVer.ps1

Войти

* RECOMMENDED * Online ROM Flash Component for Windows x64 — HP ProLiant DL360 G5 (P58) Server

Описание

Инструкции по установке

Замечания о версии

Исправления