Как установить windows на ibm

Steps

Table of Contents:
1.0 What you will need
2.0 Where to download firmware,
device drivers and files
3.0 Preparing the hardware
4.0 Installing Microsoft Windows Server 2012 R2

• 4.1 Updating firmware &
  device drivers
• 4.2 Enabling Hyper-V
• 4.3 Post installation
  instructions

5.0 Notices

Installation
Instructions for Microsoft Windows Server 2012 R2 — IBM System
x3550 M3 (7944)

Revision level: 1.00 Updated: 09 October 2013 ©
Copyright International Business Machines Corporation 2013. All
rights reserved. US Government Users Restricted Rights — Use,
duplication, or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp. Note: Before using this information
and the product it supports, read the general information in 5.0
Notices in this document. Supported servers: IBM System
x3550 M3 (7944) Follow the instructions in this document in
sequential order unless these instructions advise you otherwise.
Windows and messages might differ from those in this document.
Throughout this document, the term select is used to denote the use
of arrow keys, the Tab key, Alt + a letter combination, or the
mouse to make a selection. References to optional hardware in this
document do not imply support of that hardware. For information
about supported options, see the ServerProven® information for
your server at
http://www.ibm.com/systems/info/x86servers/serverproven/compat/us.

1.0 What
you will need

You must have the following software and hardware for the
installation:

• A licensed copy of Microsoft Windows Server 2012
  R2
• A DVD reader device
• Supported hard disk drives. See
  http://www.ibm.com/systems/info/x86servers/serverproven/compat/us/
  for the ServerProven list of supported options and
  part numbers for the server.

2.0
Where to download firmware, device drivers and files

You can download firmware, device drivers and files from the
following sites:

• IBM U.S. Support Portal: http://www.ibm.com/supportportal
• IBM Fix Central (download device driver, BIOS, firmware): http://www.ibm.com/support/fixcentral
• For countries outside the U.S., start at http://www.ibm.com

You can download product specifications from the following site:

• For IBM System x product specifications, go to
  http://www.redbooks.ibm.com/redbooks.nsf/portals/systemx

3.0
Preparing the hardware

To prepare the hardware, update system firmware, and configure hard
drives & arrays, see the IBM System x3550 M3 (7944)
Installation Guide and User’s Guide at the IBM Support Portal .

To install Windows Server 2012 R2 complete the
following steps:

1. Insert the Windows Server 2012 R2 DVD into the
   DVD drive.
2. Turn on the server.
3. When you are prompted with the message » Press any key
   to boot from cd or dvd«, press any key to start the server
   from the Windows Server 2012 R2 DVD. The files are
   copied from the setup DVD. This process takes a few minutes.
4. In the Windows Server 2012 R2 window, make the
   following selections:
   • From the Language to install list, select
     English (United States) (or other language
     preference).
   • From the Time and currency format list, select
     English (United States) (or other time &
     currency preference).
   • From the Keyboard or input method list, select
     US (or other preference).
5. Click Next.
6. Click Install Now.
7. Enter the Product Key and click
   Next to activate Windows.
8. Select the version of Windows Server 2012 R2
   you would like to install.
9. Click Next.
10. Scroll down and read the license
    agreement.
11. Select I accept the license terms and click
    Next.
12. Select Custom (advanced).
13. When Windows Server 2012 R2 Setup displays all
    hard disk storage that is available on the server, select one of
    the following options to choose or create a drive partition in
    which to install Windows Server 2012 R2:
    • Allow Setup to create a partition: To partition the
      entire hard disk as one primary partition, highlight Disk0
      unallocated space for the hard disk drive on which you
      want to install Windows Server 2012 R2, and click
      Next.
    • Create a partition: To create a partition, highlight
      Disk0 unallocated space for the hard disk drive on which you
      want to install Windows Server 2012 R2, and click
      Drive options; then, click New. You are
      prompted to indicate how much available space to allocate from the
      non-partitioned drive. Type the amount of space (in MB), and click
      Apply; then, click Next.
    • Delete a partition: Use this option to delete a previous
      partition prior to creating a partition using either method
      above.
14. Setup formats the selected partition and copies the applicable
    files to the drive partition. This process takes 30-45 minutes and
    restarts the system twice.
15. After Windows Server 2012 R2 completes, you
    are prompted to create an administrator password before you can log
    on. Enter the password twice and click Finish.
    Then Press Ctrl + Alt + Delete to sign in using
    the password you just created.
16. After you log on as the administrator, the Server
    Manager window starts. Use Server Manager
    for naming your system, networking setup and other basic setup
    tasks.
17. See section 4.1 Updating firmware and device
    drivers for instructions on obtaining the latest firmware
    and device drivers.

4.1 Updating firmware
& device drivers

To make sure that the latest device drivers and firmware for the
IBM System x3550 M3 (7944) unit are installed,
follow the instructions in the README (.txt) file that is included
with the device driver. To download the device driver and firmware
packages and the installation instructions for IBM System
x3550 M3 (7944), complete the following steps:

1. Go to http://www.ibm.com/support and the
   IBM Support Portal will automatically open.
2. Select Find a product and select
   Browse in the pop up window
3. Under Hardware expand
   Systems
4. Under Systems expand System x
   and select your system
5. Click on Select OS and check the box for
   Windows Server 2012 R2
6. Click the Submit button followed by the double
   arrow button and verify that the item listed in the right pane is
   correct.
7. Click Finish.
8. In the Flashes and alerts box click on
   More to get the complete list of firmware and
   device drivers for your system. Follow the Readme.txt file in each
   download package for installation instructions.

4.2 Enabling
Hyper-V

To enable Hyper-V (optional) under Windows
Server 2012 R2 complete the following steps:

1. Start Server Manager console
2. In the Configure this local server area of
   Server Manager main window, click Add
   roles and features
3. Click Next three times to get to the
   Select server roles page.
4. Check the box next to Hyper-V and click
   Add Features.
5. Add any desired features and click Next.
6. Click Next again and follow the next few
   screens to configure Hyper-V.
7. On the Confirm installation selections screen,
   confirm your selections and click Install.
8. Close Server Manager, and allow system to
   reboot.
9. Hyper-V configuration details for
   Windows 2012 R2 can be found at the following
   link: http://technet.microsoft.com/en-us/library/cc770901.aspx

4.3
Post-installation instructions

1. Install the latest drivers and firmware (see section 4.1).
2. Microsoft updates should be run after all
   roles and features are enabled to update the system with all the
   current hotfixes.
3. IBM recommends you review all Retain Tips related to this
   system and the Operating System you are installing. Retain Tips are
   found at http://www.ibm.com/support/us/en.
   Review the » Problem Resolution» section for your
   specific machine type/model.

5.0
Notices

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION «AS IS» WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this
statement may not apply to you. This information could include
technical inaccuracies or typographical errors. Changes are
periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice. IBM, the
IBM logo, and ibm.com are trademarks or registered trademarks of
International Business Machines Corporation in the United States,
other countries, or both. If these and other IBM trademarked terms
are marked on their first occurrence in this information with a
trademark symbol (® or ™), these symbols indicate U.S.
registered or common law trademarks owned by IBM at the time this
information was published. Such trademarks may also be registered
or common law trademarks in other countries. A current list of IBM
trademarks is available on the Web at http://www.ibm.com/legal/copytrade.shtml.
Windows is a registered trademark of Microsoft Corporation in the
United States, other countries, or both. Other company, product, or
service names may be trademarks or service marks of others.

color black/cyan yellow/cyan
timeout 10
default /default

#use the following for reference, uncomment(#) and change as needed

#title Start Vista, find and load bootmgr
#find —set-root /bootmgr
#chainloader /bootmgr

#title find and boot Linux with menu.lst already installed
#find —set-root /sbin/init
#configfile /boot/grub/menu.lst

#title SystemRescueCd-0.4.x from hard-disk
#root (hd0,0)
#kernel /rescuecd init=/linuxrc cdroot=/dev/sda1 setkmap=us
#initrd /rescuecd.igz

#title Puppy Linux on HD0
#root (hd0,0)
#kernel /puppy/vmlinuz root=/dev/rd/0 pmedia=usbflash
#initrd /puppy/initrd.gz

#title Start Recovery Console of Windows NT/2K/XP
#find —set-root /cmldr
#chainloader /cmldr
#####################################################################
# write string «cmdcons» to memory 0000:7C03 in 2 steps:
#####################################################################
### step 1. Write 4 chars «cmdc» at 0000:7C03
#write 0x7C03 0x63646D63
### step 2. Write 3 chars «ons» and an ending null at 0000:7C07
#write 0x7C07 0x00736E6F

#title Start Acronis True Image/Disk Director from ISO loaded in memory
#map —mem (hd0,0)/acronismedia.iso (hd32)
#map —hook
#chainloader (hd32)

#title Start Acronis True Image/Disk Director from ISO
##ISO file must be contiguous on disk in this case, use Sysinternals contig.exe
#map (hd0,0)/acronismedia.iso (hd32)
#map —hook
#chainloader (hd32)

#title Start MemTest from floppy image on second hard disk/third partition
##image file can be gzipped, i.e. memtest.img.gz
#map —mem (hd1,2)/memtest.img (fd0)
#map —hook
#chainloader (fd0)+1
#rootnoverify (fd0)

#title Chainload the bootsector at third partition, fifth hard disk
#chainloader (hd4,2)+1

#title Start Windows XP if it’s on second hard disk
##ntldr/ntdetect.com won’t start if are not on first disk, first active partition, thus the mapping
#map (hd1) (hd0)
#map —hook
#rootnoverify (hd0,0)
#chainloader /ntldr

#title find and load IO.SYS of Windows 9x/Me/DOS
#find —set-root /io.sys
#chainloader /io.sys

title Start PLoP boot manager\nYou may want to try it if your computer boots from USB slowly.\nOnce booted,select USB from its menu to load USB 2.0 drivers.\nPlease report any issues to its author — www.plop.at
find —set-root —ignore-cd /usbdrive.tag
kernel /plpbt.bin

title Windows XP/2000/2003 Setup
map —unmap=0:0xff
map —unhook
savedefault
find —set-root —ignore-cd /usbdrive.tag
configfile /winsetup.lst